Our stock products are being manufactured in our plants continuously in order to provide you a shortest lead time as possible.
In the following table you may find typical lead times. They may vary depending on quantity and raw material availability. Some products are having an interchangeable parts.
You will receive an accurate delvery date on your order confirmation after you ordered.
|Optomechanics||Average 2 - 5 weeks*|
|Optics||Average 2 - 5 weeks*|
|Motorized Stages||Average 3 - 6 weeks*|
|System||Average 3 – 6 weeks*|
*This is an average typical lead time. For more details, please ask to: email@example.com
The stock availability for this product is limited at the moment. Please contact the sales team for more information at firstname.lastname@example.org.
Estimated average shipping time is 2 - 10 working days. For urgent shipping please contact the sales team at email@example.com. Extra charges may applies.
At this time pre-manufactured parts are already available for a quick assembly.
The typical lead times is estimated at 1 - 3 weeks after your order, depending on quantity.
You will receive an accurate delivery date on your order confirmation after you ordered.
For more details, please ask to : firstname.lastname@example.org
Installation on top of a table or test bench makes these isolators ready for immediate use.
These tabletop vibration isolators are space-saving and effective for use with small optical systems and microscopes.
◦Rapidly attenuates vibrations transmitted to mounted equipment and instruments Ideal for mounting equipment and instruments that are affected by vibration.
◦Uses a precision air spring system for the isolation of vertical vibrations.
◦The outer frame has an integral construction, providing excellent stiffness. The mounting plate is inside the outer frame, thereby minimizing the effects of accidental contact with the outer-perimeter frame.
▶We can produce sizes not listed in the catalog. Contact our International Sales Division for more information.
▶When installed in locations with no air source, use the silent air compressor (PC-10H-S) which can be used indoors. (W6003)
▶The vibration isolator may not perform normally if used under an extremely offset load or with instruments or equipment having a very high center of gravity.
▶Because of the weight, delivery cost will be quoted separately.Use the carry-in route and installation environment question sheet. (W6001)
▶Use the Air Spring Vibration Isolator Model Selection Check Sheet to check usage, load capacity, or unclear points.(W6002)
|Natural Frequency (Vertical Direction)||about 2.0 − 2.3Hz|
|Vibration Isolation Method (Vertical Direction)||Precision air spring|
|Control Method (Vertical Direction)||Air damping by means of orifice|
|Mounting Plate Used (Part Number Suffix A)||Lonleum* bonded to steel plate (non-magnetic)|
|Mounting Plate Used (Part Number Suffix B)||Steel plate black finish (magnetic)|
|Mounting Plate Used (Part Number Suffix C)||Upper plate: magnetic stainless steel plate, thickness 5mm (unpainted), Lower plate: aluminum|
|Mounting Plate Used (Part Number Suffix D)||M6 tapped holes on 50×50mm matrix over the entire top surface of type C above|
|Mounting Plate Used (Part Number Suffix E)||M6 tapped holes on 25×25mm matrix over the entire top surface of type C above|
|Type||Automatic Vertical Leveling Type DT-A||Manual Vertical Leveling Type DT-M|
|Features||◦Equipped with an auto level sensor, if the vertical balance of the mounting plate is disturbed due to a shifting load, it automatically restores to the set height.||◦The manual leveling system is best suited for mounting
instruments that do not change position or weight.|
◦The height of the bench is easily adjusted by operating the supply and exhaust valve.
◦Air supply is provided with the accessory hand air pump, and no other air source is required.
|Air Supply||Automatically supplied from air source|
(Air compressor, factory air, etc.)
|Manually supplied with the hand air pump|
|Air Supply Pressure||0.3 − 0.7MPa (about 3 − 7kgf/cm2)||-|
|Horizontal Leveling||Automatic adjustment by means of three auto level sensors||Manual adjustment by means of three supply and exhaust valves|
|Accessories||Auto level sensor|
One air tube (5m)
|One hand air pump|
One special rotation driver for supply and exhaust valve
|* Lonleum: PVC as the main material, it is non-magnetic, but effective for stopping slippage of instruments on the mounting plate.|