Our stock products are being manufactured in our plants continuously in order to provide you a shortest lead time as possible.
In the following table you may find typical lead times. They may vary depending on quantity and raw material availability. Some products are having an interchangeable parts.
You will receive an accurate delvery date on your order confirmation after you ordered.
|Optomechanics||Average 2 - 5 weeks*|
|Optics||Average 2 - 5 weeks*|
|Motorized Stages||Average 3 - 6 weeks*|
|System||Average 3 – 6 weeks*|
*This is an average typical lead time. For more details, please ask to: firstname.lastname@example.org
The stock availability for this product is limited at the moment. Please contact the sales team for more information at email@example.com.
Estimated average shipping time is 2 - 10 working days. For urgent shipping please contact the sales team at firstname.lastname@example.org. Extra charges may applies.
At this time pre-manufactured parts are already available for a quick assembly.
The typical lead times is estimated at 1 - 3 weeks after your order, depending on quantity.
You will receive an accurate delivery date on your order confirmation after you ordered.
For more details, please ask to : email@example.com
Right-angle prism can be used as a substitute for the mirror. Independent even without a special holder, and since the choice of a variety of installation methods, it is useful if you want to reduce the size of the device. In addition, with very high accuracy and precision angle of the prism surface, it can also be used by directly bonding it to machined parts.
◦RPB1 to 3 are used as a substitute for the mirror reflection of the slope. RPB1 is coated with anti-reflection coating with two surfaces which the light is incident and emitted by using the critical angle prism reflection of the slope and the surface. RPB2 are coated with reflective coating (Al+MgF2) on the surface of slope. RPB3 is the product which does not pass through the light reflected by the inclined surface of the interior of the prism, and there are three types.
◦RPB4 can be used when you want to use the reflection of the two surfaces sandwiching the apex angle (right angle). RPB4 can be used as to when observe two opposite directions at the same time, or as a prototype orthogonal basis and so on.
◦RPB5 are used in applications where light back at the same angle as the incident light with respect to the horizontal direction. And double pass interferometer is used in (such as self-correlator) auto correlator.
▶For custom sizes and wavelengths not listed on-line or in our catalog please contact our Sales Division with your requests.
▶Prisms are also available uncoated.
▶A dimension measured is slightly shorter than the catalog size because it contains chamfer dimension. Dimensional tolerances are defined by the sides of the triangle with the slope and two bottom surface.
▶If the light is incident on the slope from the air side, most of the light through the prism side and it reflects only part of the light.
▶If the incident light at an incident angle of 41 degrees or less (less than the critical angle) from the side of the glass which is no coating on the surface, will not be total reflection but part of the light is transmitted through the air side.
▶Sometimes when dirt or fingerprints on the surface with no coating, total reflection will not happen any more than the critical angle. Do not contact anything on the no coated surface.
▶Please use RPB5 in the range of 0±5.7 degrees for the slope. Beyond this range, it will not be totally reflected.
▶RPB2 are also reflected at an angle smaller than the critical angle by Al coating, but the reflectance will be lower to 12% less than the RPB1.
|Material||BK7 (Refractive index nd＝1.517)|
|Surface flatness of substrate||λ/4|
|Angle tolerance||±1′ (90°or 45°)|
|Coating||Antireflection Coating or Al+MgF2 (Prtected coating)|
|Wavelength Range||400 - 700nm|
|Surface Quality |
|Clear aperture||Circle or ellipse that inscribed in a rectangular of 90% of the dimensions|