Our stock products are being manufactured in our plants continuously in order to provide you a shortest lead time as possible.
In the following table you may find typical lead times. They may vary depending on quantity and raw material availability. Some products are having an interchangeable parts.
You will receive an accurate delvery date on your order confirmation after you ordered.
|Optomechanics||Average 2 - 5 weeks*|
|Optics||Average 2 - 5 weeks*|
|Motorized Stages||Average 3 - 6 weeks*|
|System||Average 3 – 6 weeks*|
*This is an average typical lead time. For more details, please ask to: firstname.lastname@example.org
The stock availability for this product is limited at the moment. Please contact the sales team for more information at email@example.com.
Estimated average shipping time is 2 - 10 working days. For urgent shipping please contact the sales team at firstname.lastname@example.org. Extra charges may applies.
At this time pre-manufactured parts are already available for a quick assembly.
The typical lead times is estimated at 1 - 3 weeks after your order, depending on quantity.
You will receive an accurate delivery date on your order confirmation after you ordered.
For more details, please ask to : email@example.com
Our highest performance vibration isolation system.
Utilizing independent mechanisms for the vertical and horizontal directions, this system achieves the high performance and efficiency required for the most demanding applications.
◦This vibration isolator rapidly attenuates vibrations transmitted to mounted equipment and instruments, and is essential for mounting equipment and instruments that are affected by vibration.
◦The bench is lightweight with excellent stiffness due to the aluminum honeycomb core.
◦The top surface of the bench is magnetic stainless steel plate, with tapped holes (M6 25×25mm matrix) over the entire surface allowing both magnetic type and screw fixing type systems or equipment to be mounted.
◦The manual leveling system does not require a continuous air supply. The isolators can be pressurized with just a hand air pump.
▶We can produce sizes not listed in the catalog. Contact our International Sales Division for more information.
▶When installed in locations with no air source, use the silent air compressor (PC-10H-S) which can be used indoors. (W6003)
▶The vibration isolator may not perform normally if used under an extremely offset load or with instruments or equipment having a very high center of gravity.
▶Because of the weight, delivery cost will be quoted separately.Use the carry-in route and installation environment question sheet. (W6001)
▶Use the Air Spring Vibration Isolator Model Selection Check Sheet to check usage, load capacity, or unclear points.(W6002)
|Natural Frequency (Vertical Direction)||about 1.3Hz|
|Natural Frequency (Horizontal Direction)||about 0.5Hz|
|Vibration Isolation Method (Vertical Direction)||Precision air spring|
|Vibration Isolation Method (Horizontal Direction)||Universal mechanism|
|Control Method (Vertical Direction)||Air damping by means of orifice|
|Control Method (Horizontal Direction)||Damping with special rubber|
|Honeycomb Material inside Bench||Aluminum|
|Bench Material (Upper Plate)||Magnetic stainless steel plate, thickness 5mm|
|Bench Material (Lateral Side)||Black vinyl leatherette bonded to plywood|
|Bench Material (Lower Plate)||Regular steel plate (hot rolled steel plate), thickness 4.5mm|
|Bench Top Surface||M6 tapped holes on 25×25mm matrix over the entire surface (leaving 25mm around the edges)|
|Bench Top Surface Finish||Unpainted (satin finish)|
|Type||Automatic Vertical Leveling Type TDI-LA||Manual Vertical Leveling Type TDI-LM|
|Features||◦Equipped with an auto level sensor, if the vertical balance of the mounting plate is disturbed due to a shifting load, it automatically restores to the set height.||◦The manual leveling system is best suited for mounting instruments that do not change position or weight.|
◦The height of the bench is easily adjusted by operating the supply and exhaust valve.
◦Air supply is provided with the accessory hand air pump, and no other air source is required.
|Air Supply||Automatically supplied from air source|
(Air compressor, factory air, etc.)
|Manually supplied with the hand air pump|
|Air Supply Pressure||0.3 − 0.7MPa (about 3 − 7kgf/cm2)||-|
|Horizontal Leveling||Automatic adjustment by means of three auto level sensors||Manual adjustment by means of three supply and exhaust valves|
|Accessories||Auto level sensor|
One air tube (5m)
|One hand air pump|
One special rotation driver for supply and exhaust valve